A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter

Bindu S. J.; C. A. Babu

doi:doi:10.11648/j.jeee.20140205.11

| Peer-Reviewed

A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter

Bindu S. J., C. A. Babu

Published in Journal of Electrical and Electronic Engineering (Volume 2, Issue 5)

Received: 29 November 2014 Accepted: 7 December 2014 Published: 18 December 2014

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

Power quality is becoming an important issue for electricity consumers at all level of usages. Sensitive equipment and non-linear loads are common in both industrial and domestic environment. Harmonic distortion can result in malfunction of sensitive equipments and generators. Power factor corrected converter is increasingly used in industry to improve input current quality and regulate the output voltage of front end converter. This paper presents a Single Switch Power Quality Converter which achieves both power factor correction and output voltage regulation by using only one switch. This paper deals with the design method in the reduction of DC bus voltage stress during light load, by selecting proper boost inductor using Equal Area Criterion (EAC).

Published in	Journal of Electrical and Electronic Engineering (Volume 2, Issue 5)
DOI	10.11648/j.jeee.20140205.11
Page(s)	75-81
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2014. Published by Science Publishing Group

Keywords

Power Factor Correction, BIFRED Converter, Equal Area Criterion, Power Quality, DC Bus Voltage Stress

References

[1]	IEEE Recommended Practices and Requirements for Harmonics Control in Electric Power Systems, IEEEStandard, 519, 1992.
[2]	Limits for Harmonic Current Emissions, International Electrotechnical Commission Standard 61000-3-2,2004.
[3]	M. Madigan, R. Erickson and E. Ismail, "Integrated High Quality Rectifier Regulators" in IEEE power ELECTRONICS SPECIALIST CONF…... 1992. p.p. 1043 - 1051.
[4]	Jinrong Qian, Fred C. Lee, "Single - Stage Single - Switch p -f-c Ac/Dc converters with DC - Bus voltage feedback for universal line applications “in IEEE transactions on P.E. vol: 13, No-6 Nov 1998 p.p. 1079 – 1088
[5]	Martin H. L. Chow, Yim-Shu Lee, and Chi K. Tse “Single-Stage Single-Switch Isolated PFC Regulator with Unity Power Factor, Fast Transient Response, and Low-Voltage Stress” in IEEE Transactions on P.E., vol: 15, No-1, Jan 2000 p.p. 156 - 163
[6]	A.K Jha,B.G Fernandes and A.Kishore “A Single Phase Single Stage AC/DC converter with high input power factor and tight output regulation”in Progress in Electromagnetic Research Symposium 2006,Cambridge,USA,March 26-29.pp 322-328
[7]	James P. Noon, Alexander Borisovich, “Method to Reduce Bus Voltage Stress in Single-Stage Single Switch Power Factor Correction Circuit”, U.S.Patent 6,717,826 B 2, Apr. 6,2004.
[8]	Manjusha S. Dawande, Gopal K. Dubey, Programmable Input PFC method for SMR" in IEEE Transactions on P.E. vol: 11, No-4 July 1996 p.p. 585 – 591
[9]	C Qiao and Keyue M. Smedley, "A Topology Servey of Single - Stage P.F.C. with a Boost Type input Current - shaper." In IEEE APEC - 2000 February 6 - 10
[10]	Bindu S J, C A Babu, “Analysis and Design of a Single Stage Single Switch Power Factor Converter to reduce Bus Voltage Stress with High Input Power Factor and Fast Output Voltage Regulation”, in IEEE 13th workshop on Control and Modelling for Power Electronics (COMPEL-2012),Digital object identifier: 10.1109/COMPEL.2012.6251760

Cite This Article

Plain Text BibTeX RIS

APA Style

Bindu S. J., C. A. Babu. (2014). A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter. Journal of Electrical and Electronic Engineering, 2(5), 75-81. https://doi.org/10.11648/j.jeee.20140205.11

Copy | Download

ACS Style

Bindu S. J.; C. A. Babu. A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter. J. Electr. Electron. Eng. 2014, 2(5), 75-81. doi: 10.11648/j.jeee.20140205.11

Copy | Download

AMA Style

Bindu S. J., C. A. Babu. A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter. J Electr Electron Eng. 2014;2(5):75-81. doi: 10.11648/j.jeee.20140205.11

Copy | Download

@article{10.11648/j.jeee.20140205.11,
  author = {Bindu S. J. and C. A. Babu},
  title = {A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {2},
  number = {5},
  pages = {75-81},
  doi = {10.11648/j.jeee.20140205.11},
  url = {https://doi.org/10.11648/j.jeee.20140205.11},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20140205.11},
  abstract = {Power quality is becoming an important issue for electricity consumers at all level of usages. Sensitive equipment and non-linear loads are common in both industrial and domestic environment. Harmonic distortion can result in malfunction of sensitive equipments and generators. Power factor corrected converter is increasingly used in industry to improve input current quality and regulate the output voltage of front end converter. This paper presents a Single Switch Power Quality Converter which achieves both power factor correction and output voltage regulation by using only one switch. This paper deals with the design method in the reduction of DC bus voltage stress during light load, by selecting proper boost inductor using Equal Area Criterion (EAC).},
 year = {2014}
}

Copy | Download

TY  - JOUR
T1  - A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter
AU  - Bindu S. J.
AU  - C. A. Babu
Y1  - 2014/12/18
PY  - 2014
N1  - https://doi.org/10.11648/j.jeee.20140205.11
DO  - 10.11648/j.jeee.20140205.11
T2  - Journal of Electrical and Electronic Engineering
JF  - Journal of Electrical and Electronic Engineering
JO  - Journal of Electrical and Electronic Engineering
SP  - 75
EP  - 81
PB  - Science Publishing Group
SN  - 2329-1605
UR  - https://doi.org/10.11648/j.jeee.20140205.11
AB  - Power quality is becoming an important issue for electricity consumers at all level of usages. Sensitive equipment and non-linear loads are common in both industrial and domestic environment. Harmonic distortion can result in malfunction of sensitive equipments and generators. Power factor corrected converter is increasingly used in industry to improve input current quality and regulate the output voltage of front end converter. This paper presents a Single Switch Power Quality Converter which achieves both power factor correction and output voltage regulation by using only one switch. This paper deals with the design method in the reduction of DC bus voltage stress during light load, by selecting proper boost inductor using Equal Area Criterion (EAC).
VL  - 2
IS  - 5
ER  -

Copy | Download

Author Information

Bindu S. J.
C. A. Babu

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Bindu S. J., C. A. Babu. (2014). A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter. Journal of Electrical and Electronic Engineering, 2(5), 75-81. https://doi.org/10.11648/j.jeee.20140205.11

Copy | Download

ACS Style

Bindu S. J.; C. A. Babu. A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter. J. Electr. Electron. Eng. 2014, 2(5), 75-81. doi: 10.11648/j.jeee.20140205.11

Copy | Download

AMA Style

Bindu S. J., C. A. Babu. A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter. J Electr Electron Eng. 2014;2(5):75-81. doi: 10.11648/j.jeee.20140205.11

Copy | Download

@article{10.11648/j.jeee.20140205.11,
  author = {Bindu S. J. and C. A. Babu},
  title = {A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {2},
  number = {5},
  pages = {75-81},
  doi = {10.11648/j.jeee.20140205.11},
  url = {https://doi.org/10.11648/j.jeee.20140205.11},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20140205.11},
  abstract = {Power quality is becoming an important issue for electricity consumers at all level of usages. Sensitive equipment and non-linear loads are common in both industrial and domestic environment. Harmonic distortion can result in malfunction of sensitive equipments and generators. Power factor corrected converter is increasingly used in industry to improve input current quality and regulate the output voltage of front end converter. This paper presents a Single Switch Power Quality Converter which achieves both power factor correction and output voltage regulation by using only one switch. This paper deals with the design method in the reduction of DC bus voltage stress during light load, by selecting proper boost inductor using Equal Area Criterion (EAC).},
 year = {2014}
}

Copy | Download

TY  - JOUR
T1  - A Design Solution to Reduce DC Bus Voltage Stress in Single Switch Power Quality Converter
AU  - Bindu S. J.
AU  - C. A. Babu
Y1  - 2014/12/18
PY  - 2014
N1  - https://doi.org/10.11648/j.jeee.20140205.11
DO  - 10.11648/j.jeee.20140205.11
T2  - Journal of Electrical and Electronic Engineering
JF  - Journal of Electrical and Electronic Engineering
JO  - Journal of Electrical and Electronic Engineering
SP  - 75
EP  - 81
PB  - Science Publishing Group
SN  - 2329-1605
UR  - https://doi.org/10.11648/j.jeee.20140205.11
AB  - Power quality is becoming an important issue for electricity consumers at all level of usages. Sensitive equipment and non-linear loads are common in both industrial and domestic environment. Harmonic distortion can result in malfunction of sensitive equipments and generators. Power factor corrected converter is increasingly used in industry to improve input current quality and regulate the output voltage of front end converter. This paper presents a Single Switch Power Quality Converter which achieves both power factor correction and output voltage regulation by using only one switch. This paper deals with the design method in the reduction of DC bus voltage stress during light load, by selecting proper boost inductor using Equal Area Criterion (EAC).
VL  - 2
IS  - 5
ER  -

Copy | Download